The generic authentication service process (authd) could not open a socket during the indicated operation. The authentication service process is a security service that verifies an identity that is claimed by or for a system entity. The AUTHD_SOCKET_FAILED message is logged each time the authentication service process fails to open a socket connection. When an … [Read more...]
Spontaneous high Routing Engine CPU utilization
While processing updates, the Routing Engine (RE) CPU may show a utilization spike for a couple of seconds. This is normal behavior and can be safely ignored. Sometimes the Routing Engine (RE) CPU may spike for a couple of seconds. This spontaneous RE CPU spike is generally observed during processing updates. This may include RPD updates like route updates (which cannot be … [Read more...]
CHASSISD_RE_OVER_TEMP_WARNING
The CHASSISD_RE_OVER_TEMP_WARNING message is reported into the system message file whenever the Routing Engine (RE) exceeds the upper temperature threshold. If the temperature does not go below the threshold within four minutes after the chassis process (chassisd) detects this condition, the chassisd process shuts down the indicated component. When this message was logged, the … [Read more...]
LIBSERVICED_SOCKET_PRIVATIZE
An attempt to attach a socket to the management routing instance for communication between the Routing Engine and GGSN-C PICs failed. The LIBSERVICED_SOCKET_PRIVATIZE message is logged each time there is a failed attempt to attach a socket to the management routing instance for communication between the Routing Engine and GGSN-C PICs. When an attempt to attach a socket to … [Read more...]
LIBMSPRPC_CLIENT_NO_REPLY
LIBMSPRPC_CLIENT_NO_REPLY Remote execution of the command given from the Routing Engine (RE) to the PIC failed. There was no reply from the PIC. This message is generated by the mspinfo process, which is responsible for RPC (Remote Procedure Call) communication between the Routing Engine and the Multiservices PICs. This only applies to M-series and T-series routers, and … [Read more...]
DFCD_LINH_MALLOC_FAILED
The dynamic flow capture process (dfcd) could not allocate memory for linh message. The problem related to this syslog message is described in the following sections: An error similar to the following is reported: DFCD_LINH_MALLOC_FAILED, LOG_ERR, "GENCFG mem alloc failed !!! Dynamic flow capture enables you to capture packet flows on the basis of dynamic filtering … [Read more...]
RMON_EVENT_re_high_dram_utilization
High DRAM (Dynamic Random Access Memory ) CPU utilization on RE (Routing Engine). The SNMP variable being reported is jnxOperatingBuffer.9.1.0.0. The OID value for this variable is 1.3.6.1.4.1.2636.3.1.13.1.11.9.1.0.0. The problem related to this syslog message is described in the following sections: The RMON_EVENT_re_high_dram_utilization message is logged each time the … [Read more...]
SRX 5000 Series routing engine 1 upgrade procedure
SRX 5000 Series routing engine 1 upgrade procedure On SRX systems, the routing engine (RE) at slot 1 (0 based) RE1 is needed for dual control link redundancy and runs in single user mode. The normal upgrade process is not applicable to it and mostly not needed. However, there may be instances when the RE at slot 1 (called RE1 hereafter) needs to be upgraded. This article … [Read more...]
COSD_GENCFG_WRITE_FAILED
This article describes the following syslog message: COSD_GENCFG_WRITE_FAILED The class-of-service process (COSD) uses GENCFG to read/write data from the kernel. If the write fails, the kernel returns an error. The reason for the failure is given after the message, as in the following log example: COSD_GENCFG_WRITE_FAILED: GENCFG write failed for Classifier to IFL 74. … [Read more...]
KERNEL: rdp retransmit error
The kernel on the controller (e.g., Routing Engine) is having difficulty communicating with the PFE (Packet Forwarding Engine). The problem related to this syslog message is described in the following sections: The KERNEL: rdp retransmit error message is logged whenever the kernel on the controller is having difficulty communicating with the Packet Forwarding Engine … [Read more...]