PFE notification: Getfail packets. The number of notification cells ignored because DMA (direct memory access) memory could not be allocated. The RMON_EVENT_pfe_getfail_notification message is logged each time the packet forwarding engine (pfe) is not able to allocate memory for notification cells. When an RMON_EVENT_pfe_getfail_notification event occurs, a message similar … [Read more...]
The ‘bgp-igp-both-ribs’ knob does not work in LSP that is made by a dynamic tunnel
This article describes the issue of the bgp-igp-both-ribs knob not working in LSP, which is made by a dynamic tunnel. The bgp-igp-both-ribs knob is not working in LSP, which is made by a dynamic tunnel. The bgp-igp-both-ribs knob works only with point to point LSPs. The LSP is not installed in inet.0 for the dynamic LSPs being created. For example, the P2MP LSP cannot be … [Read more...]
RADIUS accounting in MX has Framed-IP-Netmask of IP Pool
How do you define Framed-IP-Netmask 255.255.255.255 in RADIUS accounting? By default, the MX router will send Framed-IP-Netmask as IP Pool. [edit access address-assignment pool test] jtac@ERX-MX480-1-RE0# show family inet { network 10.220.32.0/24; range test { low 10.220.32.1; high 10.220.32.255; } } No. Time Source … [Read more...]
SERVICED_COMMAND_FAILED
An error caused a command being executed on an interface client to be canceled. The SERVICED_COMMAND_FAILED message is logged each time a command executing on an interface client is cancelled. When a SERVICED_COMMAND_FAILED event occurs, a message similar to the following is reported: serviced[3503]: SERVICED_COMMAND_FAILED: nod_connect_failed_cb: remote command … [Read more...]
VRRP Advertisement sent/received counters
This article describes the issue of the VRRP PDU interface's statistics advertisement not always correctly populating the count. The VRRP PDU statistics, which displays the interface's advertisement for sent and/or received, is displaying the count as 0 or in certain cases, it will display a negative count. This issue is due to a software bug or in certain cases, the sent … [Read more...]
SRX5600 and SRX5800 FXP0 interface uses non-Juniper MAC address
On SRX5600 and SRX5800 devices, the out-of-band management interface fpx0 has a non-Juniper MAC address. Juniper devices normally use the Juniper MAC addresses on their interfaces. However there is an exception with the out-of-band management interface fxp0 on the SRX5600 and SRX5800 platforms, where the MAC address is not from a Juniper MAC address … [Read more...]
AUTHD_SOCKET_FAILED
The generic authentication service process (authd) could not open a socket during the indicated operation. The authentication service process is a security service that verifies an identity that is claimed by or for a system entity. The AUTHD_SOCKET_FAILED message is logged each time the authentication service process fails to open a socket connection. When an … [Read more...]
How to edit, save, and quit without saving in the VI editor
How to edit, save, and quit without saving in the VI editor. To quit the VI editor and save changes, perform the following procedure: 1.If you are currently in the insert or append mode, press Esc. 2.Press : (colon). The cursor will be re-displayed at the lower left corner of the screen, besides a colon prompt. 3.Type q!. This will quit the editor and all changes that … [Read more...]
Triggering operating mode conversion for PIM protocol from sparse to dense
This article discusses two configuration knobs used to trigger the conversion of operating mode for the PIM protocol from sparse to dense. The default operating mode for the PIM protocol is sparse mode. For this reason, when a multicast stream is received on an interface operating in sparse-dense mode, the stream will be forwarded by means of sparse mode rules unless one of … [Read more...]
RPD_DYN_CFG_GET_PROF_NAME_FAILED
The Routing Protocol Dynamic Configuration Get Profile Name process failed to retrieve the Profile Name from the session snapshot. When a RPD_DYN_CFG_GET_PROF_NAME_FAILED event occurs, a message similar to the following is reported: router[13677]: RPD_DYN_CFG_GET_PROF_NAME_FAILED: Get profile name for session 1280 failed: -7 The cause may be due to a memory error, an … [Read more...]