CCNA 4 Connecting Networks v6.0 Practice Skills Assessment

CCNA 4 Connecting Networks v6.0 CN Practice Skills Assessment – PT

CCNA Routing and Switching Connecting Networks

Skill-Based Assessment – Packet Tracer

FORM 0
CCNA 4 Connecting Networks v6.0 Practice Skills Assessment
A few things to keep in mind while completing this activity:

  1.  Do not use the browser Back button or close or reload any Exam windows during the exam.
  2.  Do not close Packet Tracer when you are done. It will close automatically.
  3.  Click the Submit Assessment button to submit your work.

Objectives

In this Packet Tracer Skills Based Assessment, you will do as follows:

  • Configure PPP encapsulation and CHAP authentication for serial links.
  • Configure a GRE tunnel.
  • Configure OSPF.
  • Configure BGP.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

For the sake of time, many repetitive, but important, configuration tasks have been omitted from this assessment. Many of these tasks, especially those related to security, are essential elements of a network configuration. The intent of this activity is not to diminish the importance of full device configurations.

The IP addresses for all the devices have been configured and some of the routing configurations are already completed in this activity.

You are required to configure the devices as follows:

Branch:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard IPv4 ACL.

Customer:

  • Configure standard IPv4 ACLs.

HQ:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

Note: All the routers in AS 65001 are locked and no configurations are performed by the students. Furthermore, all the switches are pre-configured.

Addressing Table

CCNA 4 Connecting Networks v6.0 Practice Skills Assessment ADDRESS TABLE

Instructions

Step 1: Configure PPP encapsulation and authentication.

  • Configure PPP encapsulation for the link between HQ and ISP1 and the link between Branch and ISP1.
  •  Configure CHAP authentication between the links.
  •  Configure the correct username and the password cisco123 for CHAP authentication on both HQ and Branch.

Step 2: Configure a GRE tunnel with routing.

  •   Configure a GRE tunnel between HQ and Branch.
  •   Configure OSPF 1 to route the traffic between the LANs of HQ and Branch through the GRE tunnel. Summarize the networks attached to Branch.

Step 3: Configure BGP.

Configure BGP between ISP1 in Internet cluster and 209.165.202.128/27 network on HQ.

  •   Use AS number 65020 for HQ.
  •   Configure ISP1 as the BGP neighbor.
  •  Only advertise the 209.165.202.128 / 27 network into BGP.

Step 4: Configure ACLs for NAT.

  •  Configure a standard access list numbered 1 on Branch to allow NAT for hosts in network 192.168.0.0 /23.
  •  Configure a standard access list numbered 1 on HQ to allow NAT for hosts in network 192.168.2.0 /24.
  •  Configure a standard access list numbered 1 on Customer to allow NAT for hosts in network 192.168.3.0 /24.

Step 5: Configure a standard ACL to restrict remote access to the Customer router.

A standard ACL named VTY_ADMIN is configured to limit access via VTY to the Customer router. This ACL will only allow hosts from the LAN attached to the G0/1 interface and the hosts from the LANs on Branch router to access the Customer router. All the other connections to VTY should fail.

  • Configure one ACL named VTY_ADMIN with three ACEs in the following order:
  1.  Allow any hosts from the LAN attached to the G0/1 interface of Customer router to access the router.
  2.  Allow the hosts from the LANs in the Branch network to Customer router remotely.
  3.  All other remote connections are denied.
  •  Apply the ACL to the appropriate interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 6: Configure an extended ACL to restrict access to the HQ LAN.

  • Configure an extended ACL named HTTP_ACCESS that allows Branch LANs, Customer LANs and the LAN inside HQ to access HQ-Server via the web browser.

Configure this ACL with the following 5 ACEs in the following order:

  1.  Allow the hosts from the Branch network to access the HQ-Server.
  2. Allow the hosts from the Customer LANs to access the HQ-Server.
  3. Allow the internal network 192.168.2.0 /24 to access the HQ-Server.
  4.  Allow ICMP replies to HQ-Server from any networks.

Explicitly deny all other traffic from accessing the HQ-Server.

  • Apply the ACL to the HQ G0/1 interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 7: Configure an IPv6 access list to restrict access to the HQ LAN.

  • Configure an IPv6 access list named HTTP6_ACCESS that allows Branch LANs, Customer LANs and the LAN inside HQ to access HQ-Server via the web browser.
  •  Configure this ACL with the following 6 ACEs in the following order:
  1.  Allow the hosts from the Branch (2001:DB8:ACAD::/64) to access the HQ-Server.
  2.  Allow the hosts from the Branch (2001:DB8:ACAD:1::/64) to access the HQ-Server.
  3.  Allow the hosts from the Customer LANs to access the HQ-Server.
  4. Allow the internal network 2001:DB8:ACAD:2::/64 to access the HQ-Server.
  5. Allow ICMP from HQ-Server to the other networks.
  6. Explicitly deny all) other traffic from accessing the HQ-Server.
  7. Apply the ACL to the HQ G0/1 interface.

Answers – Intructions

On Router: HQ – Main – Corp (Note: Username & Password for CHAP authentication)

On Router: Branch – Remote – Branch1 (Note: Username & Password for CHAP authentication)

On Router: Customer – Other – Branch2

FORM 1
CCNA 4 Connecting Networks v6.0 Practice Skills Assessment

Objectives

In this Packet Tracer Skills Based Assessment, you will do as follows:

  • Configure PPP encapsulation and CHAP authentication for serial links.
  • Configure a GRE tunnel.
  • Configure OSPF.
  • Configure BGP.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

For the sake of time, many repetitive, but important, configuration tasks have been omitted from this assessment. Many of these tasks, especially those related to security, are essential elements of a network configuration. The intent of this activity is not to diminish the importance of full device configurations.

The IP addresses for all the devices have been configured and some of the routing configurations are already completed in this activity.

You are required to configure the devices as follows:

Remote:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard IPv4 ACL.

Other:

  • Configure standard IPv4 ACLs.

Main:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

Note: All the routers in AS 65001 are locked and no configurations are performed by the students. Furthermore, all the switches are pre-configured.

Addressing Table

CCNA 4 Connecting Networks v6.0 Practice Skills Assessment ADDRESS TABLE

Instructions

Step 1: Configure PPP encapsulation and authentication.

  • Configure PPP encapsulation for the link between Main and ISP1 and the link between Remote and ISP1.
  • Configure CHAP authentication between the links.
  • Configure the correct username and the password 321cisco for CHAP authentication on both Main and Remote.

Step 2: Configure a GRE tunnel with routing.

  • Configure a GRE tunnel between Main and Remote.
  • Configure OSPF 1 to route the traffic between the LANs of Main and Remote through the GRE tunnel. Summarize the networks attached to Remote.

Step 3: Configure BGP.

Configure BGP between ISP1 in Internet cluster and 209.165.202.128/27 network on Main.

  • Use AS number 65020 for Main.
  • Configure ISP1 as the BGP neighbor.
  • Only advertise the 209.165.202.128 / 27 network into BGP.

Step 4: Configure ACLs for NAT.

  • Configure a standard access list numbered 1 on Remote to allow NAT for hosts in network 192.168.0.0 /23.
  • Configure a standard access list numbered 1 on Main to allow NAT for hosts in network 192.168.2.0 /24.
  • Configure a standard access list numbered 1 on Other to allow NAT for hosts in network 192.168.3.0 /24.

Step 5: Configure a standard ACL to restrict remote access to the Other router.

A standard ACL named VTY_ADMIN is configured to limit access via VTY to the Other router. This ACL will only allow hosts from the LAN attached to the G0/1 interface and the hosts from the LANs on Remote router to access the Other router. All the other connections to VTY should fail.

  • Configure one ACL named VTY_ADMIN with three ACEs in the following order:
  1. Allow any hosts from the LAN attached to the G0/1 interface of Other router to access the router.
  2. Allow the hosts from the LANs in the Remote network to Other router remotely.
  3. All other remote connections are denied.
  4. Apply the ACL to the appropriate interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 6: Configure an extended ACL to restrict access to the Main LAN.

  • Configure an extended ACL named HTTP_ACCESS that allows Remote LANs, Other LANs and the LAN inside Main to access Main-Server via the web browser.
  1. Configure this ACL with the following 5 ACEs in the following order:
  2. Allow the hosts from the Remote network to access the Main-Server.
  3. Allow the hosts from the Other LANs to access the Main-Server.
  4. Allow the internal network 192.168.2.0 /24 to access the Main-Server.
  5. Allow ICMP replies to Main-Server from any networks.
  6. Explicitly deny all other traffic from accessing the Main-Server.
  • Apply the ACL to the Main G0/1 interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 7: Configure an IPv6 access list to restrict access to the Main LAN.

  • Configure an IPv6 access list named HTTP6_ACCESS that allows Remote LANs, Other LANs and the LAN inside Main to access Main-Server via the web browser.
  • Configure this ACL with the following 6 ACEs in the following order:
  1. Allow the hosts from the Remote (2001:DB8:ACAD::/64) to access the Main-Server.
  2. Allow the hosts from the Remote (2001:DB8:ACAD:1::/64) to access the Main-Server.
  3. Allow the hosts from the Other LANs to access the Main-Server.
  4. Allow the internal network 2001:DB8:ACAD:2::/64 to access the Main-Server.
  5. Allow ICMP from Main-Server to the other networks.
  6. Explicitly deny all other traffic from accessing the Main-Server.
  7. c.  Apply the ACL to the Main G0/1 interface.

Answers – Intructions

On Router: HQ – Main – Corp (Note: Username & Password for CHAP authentication)

On Router: Branch – Remote – Branch1 (Note: Username & Password for CHAP authentication)

On Router: Customer – Other – Branch2

FORM 2 
CCNA 4 Connecting Networks v6.0 Practice Skills Assessment

Objectives

In this Packet Tracer Skills Based Assessment, you will do as follows:

  • Configure PPP encapsulation and CHAP authentication for serial links.
  • Configure a GRE tunnel.
  • Configure OSPF.
  • Configure BGP.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

For the sake of time, many repetitive, but important, configuration tasks have been omitted from this assessment. Many of these tasks, especially those related to security, are essential elements of a network configuration. The intent of this activity is not to diminish the importance of full device configurations.

The IP addresses for all the devices have been configured and some of the routing configurations are already completed in this activity.

You are required to configure the devices as follows:

Branch1:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard IPv4 ACL.

Branch2:

  • Configure standard IPv4 ACLs.

Corp:

  • Configure PPP and CHAP authentication on the appropriate interface.
  • Configure GRE tunnel.
  • Configure OSPF.
  • Configure standard and extended IPv4 ACLs.
  • Configure IPv6 ACLs.

Note: All the routers in AS 65001 are locked and no configurations are performed by the students. Furthermore, all the switches are pre-configured.

Addressing Table

CCNA 4 Connecting Networks v6.0 Practice Skills Assessment ADDRESS TABLE

Instructions

Step 1: Configure PPP encapsulation and authentication.

  • Configure PPP encapsulation for the link between Corpand ISP1 and the link between Branch1 and ISP1.
  • Configure CHAP authentication between the links.
  • Configure the correct username and the password Ciscofor CHAP authentication on both Corp and Branch1.

Step 2: Configure a GRE tunnel with routing.

  • Configure a GRE tunnel between Corpand Branch1.
  • Configure OSPF 1to route the traffic between the LANs of Corp and Branch1 through the GRE tunnel. Summarize the networks attached to Branch1.

Step 3: Configure BGP.

Configure BGP between ISP1 in Internet cluster and 209.165.202.128/27 network on Corp.

  • Use AS number 65020for Corp.
  • Configure ISP1as the BGP neighbor.
  • Only advertise the 209.165.202.128 / 27network into BGP.

Step 4: Configure ACLs for NAT.

  • Configure a standard access list numbered 1on Branch1 to allow NAT for hosts in network 192.168.0.0 /23.
  • Configure a standard access list numbered 1on Corp to allow NAT for hosts in network 192.168.2.0 /24.
  • Configure a standard access list numbered 1on Branch2 to allow NAT for hosts in network 192.168.3.0 /24.

Step 5: Configure a standard ACL to restrict remote access to the Branch2 router.

A standard ACL named VTY_ADMIN is configured to limit access via VTY to the Branch2 router. This ACL will only allow hosts from the LAN attached to the G0/1 interface and the hosts from the LANs on Branch1 router to access the Branch2 router. All the other connections to VTY should fail.

  •  Configure one ACL named VTY_ADMINwith three ACEs in the following order:
  1. Allow any hosts from the LAN attached to the G0/1 interface of Branch2 router to access the router.
  2. Allow the hosts from the LANs in the Branch1 network to Branch2 router remotely.
  3. All other remote connections are denied.
  4. Apply the ACL to the appropriate interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 6: Configure an extended ACL to restrict access to the Corp LAN.

  • Configure an extended ACL named HTTP_ACCESSthat allows Branch1 LANs, Branch2 LANs and the LAN inside Corp to access Corp-Server via the web browser.
  1. Configure this ACL with the following 5 ACEs in the following order:
  2. Allow the hosts from the Branch1 network to access the Corp-Server.
  3. Allow the hosts from the Branch2 LANs to access the Corp-Server.
  4. Allow the internal network 192.168.2.0 /24 to access the Corp-Server.
  5. Allow ICMP replies to Corp-Server from any networks.
  6. Explicitly deny all other traffic from accessing the Corp-Server.
  • Apply the ACL to the CorpG0/1 interface.

Note: Use the public IPv4 addresses in the ACLs when the private IPv4 addresses have been mapped to public IPv4 addresses.

Step 7: Configure an IPv6 access list to restrict access to the Corp LAN.

  • Configure an IPv6 access list named HTTP6_ACCESSthat allows Branch1 LANs, Branch2 LANs and the LAN inside Corp to access Corp-Server via the web browser.
  • Configure this ACL with the following 6 ACEs in the following order:
  1. Allow the hosts from the Branch1 (2001:DB8:ACAD::/64) to access the Corp-Server.
  2. Allow the hosts from the Branch1 (2001:DB8:ACAD:1::/64) to access the Corp-Server.
  3.  Allow the hosts from the Branch2 LANs to access the Corp-Server.
  4. Allow the internal network 2001:DB8:ACAD:2::/64 to access the Corp-Server.
  5. Allow ICMP from Corp-Server to the other networks.
  6. Explicitly deny all other traffic from accessing the Corp-Server.
  • Apply the ACL to the CorpG0/1 interface.

Answers – Intructions

On Router: HQ – Main – Corp (Note: Username & Password for CHAP authentication)

On Router: Branch – Remote – Branch1 (Note: Username & Password for CHAP authentication)

On Router: Customer – Other – Branch2

More Resources

About the author

James Palmer

Leave a Comment